Back to Knowledge CenterTechnical guide

128 Mbit SPI NOR Flash: Winbond, GigaDevice, Macronix

Compare four 128 Mbit SPI NOR flash parts by voltage, package, JEDEC ID and quad-read settings. Check firmware and PCB fit before qualifying a substitute.

Published · Updated · By KETA Sourcing Team

Technical guide

W25Q128JVSIQ, GD25Q128ESIGR and MX25L12835FMI-10G are 3 V-class 128 Mbit SPI NOR parts. Before qualifying a substitution, check the board footprint, the flash ID accepted by the bootloader, the Quad Enable setting and the timing for the read command you actually use. W25Q128JWSIQ is the 1.8 V-class part and needs a board with the appropriate supply and I/O levels. The MX25L12835FMI-10G comes in a 16-pin, 300 mil SOP package that cannot be soldered onto an 8-pin SOIC footprint and requires a different PCB land pattern.

Compare the exact ordering codes

W25Q128JVSIQ GD25Q128ESIGR MX25L12835FMI-10G W25Q128JWSIQ
Capacity
128 Mbit 128 Mbit 128 Mbit 128 Mbit
Operating supply
2.7–3.6 V 2.7–3.6 V 2.7–3.6 V 1.7–1.95 V
Max. SPI clock
133 / 133 / 133 MHz¹ 133 / 133 / 133 MHz² 104 / 104 / 104 MHz³ 104 / 104 / 133 MHz⁴
Package and nominal width class
8-pin SOIC, 208 mil 8-pin SOP, 208 mil 16-pin SOP, 300 mil 8-pin SOIC, 208 mil
Operating temperature
−40 to +85 °C −40 to +85 °C −40 to +85 °C −40 to +85 °C
Programmable page
256 bytes 256 bytes 256 bytes 256 bytes
Erase granularity
4 KB sector; 32 / 64 KB blocks 4 KB sector; 32 / 64 KB blocks 4 KB sector; 32 / 64 KB blocks 4 KB sector; 32 / 64 KB blocks
Typical program and erase times⁵
0.4 / 45 / 120 / 150 / 40 0.5 / 45 / 150 / 250 / 50 0.5 / 30 / 150 / 280 / 50 0.8 / 45 / 120 / 150 / 40
Program/erase endurance
100,000 cycles min. per sector 100,000 cycles min. 100,000 cycles typ. 100,000 cycles min.
Data retention
Over 20 years 20 years typ. 20 years min. at 55 °C Over 20 years
JEDEC ID (hex, manufacturer / device)
EF / 40 18 C8 / 40 18 C2 / 20 18 EF / 60 18
QE default and location
Fixed at 1 for this suffix; SR2 bit 1 (S9) 0; SR2 bit 1 (S9) 0; status register bit 6 Fixed at 1 for this suffix; SR2 bit 1 (S9)
SFDP
Yes, 5Ah Yes, 5Ah Yes, 5Ah Yes, 5Ah
Security registers / OTP storage
3 × 256 bytes, OTP locks 3 × 1,024 bytes, OTP locks 4 Kbit secured OTP area; separate access mode 3 × 256 bytes, OTP locks
Deep power-down
B9h to enter, ABh to release B9h to enter, ABh to release B9h to enter, ABh to release B9h to enter, ABh to release

Table notes

The clock figures are in single, dual and quad SPI fast-read order.

  1. Winbond JV. Up to 133 MHz at 3.0–3.6 V and up to 104 MHz across 2.7–3.6 V. Basic read (03h) is limited to 50 MHz.
  2. GigaDevice. Up to 133 MHz at 3.0–3.6 V with DC = 1. At lower supply or with DC = 0, the ceiling is 104 MHz. For dual and quad I/O, use the dummy-cycle count specified for the selected DC setting and opcode. Basic read (03h) is limited to 80 MHz.
  3. Macronix. The ordered speed grade is 104 MHz. Default dual and quad I/O reads are limited to 84 MHz. Select the datasheet dummy-cycle setting for the chosen opcode to reach 104 MHz. Basic read (03h) is limited to 50 MHz.
  4. Winbond JW. The 133 MHz ceiling applies only to SPI Quad I/O read (EBh) below 85 °C with a 4-byte-aligned start address. Other fast reads are limited to 104 MHz. Basic read (03h) is limited to 50 MHz.
  5. Typical program and erase times. The order is page program, sector erase, 32 KB block erase, 64 KB block erase and chip erase. The first four numbers are in milliseconds, and the last is in seconds. For firmware timeouts, use the relevant maximum from the datasheet.

Manufacturer datasheets: Winbond JV, GigaDevice GD25Q128E, Macronix MX25L12835F and Winbond JW.

1.52.02.53.03.54.0W25Q128JVSIQ2.7–3.6 VGD25Q128ESIGR2.7–3.6 VW25Q128JWSIQ1.7–1.95 VMX25L12835FMI-10G2.7–3.6 V
Operating supply voltage. Each bar spans the specified operating range for the exact ordering code. Clock limits and their conditions are listed in the comparison table above. W25Q128JWSIQ is a 1.8 V device and is not a drop-in replacement on 3 V boards.

Firmware checks before substituting a part

Check the full JEDEC ID. Read it in basic SPI mode on the target board. Compare the complete manufacturer and device ID with the allowlist in the boot chain, recovery tools and production programmer. The Winbond parts share a manufacturer byte and report different device IDs. Confirm that the boot ROM can start the alternate before relying on a driver update later in the boot sequence.

Check how the driver enables quad mode. Winbond and GigaDevice document a dedicated SR2 write command (31h). The two Winbond IQ parts already have QE fixed high, while the GigaDevice part ships with QE clear. Macronix uses Write Status Register (01h) for QE, with the byte count determining whether the configuration register is written as well. Read the register first, preserve protection and lock bits, and read it back before switching lanes. Verify how the board biases the shared write-protect and hold or reset pins at startup.

Match the read opcode, dummy cycles and clock. Use the actual supply range and operating temperature. For example, GigaDevice's DC bit changes the dummy-cycle count for dual and quad I/O reads. With the Macronix part, check the ordered speed grade alongside the timing table for the chosen read command. Test boot, readback, program and erase on the board. Include wake from deep power-down and execution from flash if used.

A shared driver can carry per-device settings for the ID, clocks and read commands. Use a device-specific path where register writes, protection or OTP access differ. SFDP helps the driver discover parameters, but the boot ROM and the factory programmer still need to accept the part.

During qualification, capture the working board's boot transactions so you can compare them with the alternate part. Test with the intended production image and with a blank sample, since a previous programming step may have left a different status-register configuration. After programming, cycle power and confirm that the boot path, protection settings and recovery procedure still work. If the firmware stores calibration or identity data in the security area, check that the alternate has room for it and validate the read and lock procedure on a sample.

W25Q128JVSIQSOIC-8 · 208 mil · top viewQE fixed at 1 · SR2 bit 1 (S9)1/CS8VCC2DOIO17/HOLD /RESETIO33/WPIO26CLK4GND5DIIO0IO2 and IO3 enabled for Quad SPI./HOLD is disabled at fixed QE = 1.GD25Q128ESIGRSOP-8 · 208 mil · top viewQE defaults to 0 · SR2 bit 1 (S9)1/CS8VCC2SOIO17/HOLD /RESETIO33/WPIO26SCLK4VSS · GND5SIIO0QE = 0: /WP and /HOLD or /RESET.Set QE = 1 to enable IO2 and IO3.W25Q128JWSIQSOIC-8 · 208 mil · top viewQE fixed at 1 · SR2 bit 1 (S9)1/CS8VCC2DOIO17/HOLD /RESETIO33/WPIO26CLK4GND5DIIO0IO2 and IO3 enabled for Quad SPI./HOLD is disabled at fixed QE = 1.MX25L12835FMI-10GSOP-16 · 300 mil · top viewQE defaults to 0 · status bit 61DNUSIO316SCLK2VCC15SISIO03/RESET14NC4NC13NC5NC12NC6NC11NC7/CS10GND8SOSIO19/WPSIO2QE = 1 enables SIO2 and SIO3./RESET has its own pin (pin 3).
Pin assignments and Quad Enable. Blue marks the Winbond IQ parts with QE fixed high. Amber marks parts that ship with QE clear and require it to be set for quad operation. The Macronix ordering code uses a 16-lead footprint. Pin labels follow the device datasheets; the drawing is schematic.

JV and JW: verify the voltage before ordering

The family letters immediately before the shared SIQ ending are JV for W25Q128JVSIQ and JW for W25Q128JWSIQ. Start with those letters on both the purchase order and the label. A 3.3 V supply exceeds the JW absolute maximum supply rating of 2.5 V and can damage it. Even on the correct supply, a directly driven 3.3 V logic line exceeds the JW pin DC limit of VCC + 0.4 V. Check the supply and logic thresholds for every connected signal and qualify level translation where needed before applying power.

SOIC-8 body width and solder fit

Treat 150 mil and 208 mil SOIC-8 as separate footprints unless the board drawing and assembly tolerances support both. In the Winbond narrow SOIC drawing, the lead span is 5.80–6.20 mm. The Winbond JV and JW wide drawings list 7.90 mm nominal, as does the GigaDevice drawing. Compare the body outline, lead span, pitch and pin assignments with the actual board and have the assembler verify solder joint geometry. The specified 300 mil Macronix part uses a 16-lead footprint, so plan a different footprint if the board only has pads for the 8-lead part.

What to specify on a purchase order

Use the full ordering code and confirm the packaging method. Winbond's S identifies the 208 mil outline, I the industrial grade and Q the fixed-QE option. The Winbond ordering notes list tube as the standard bulk format and ask buyers to specify tape and reel or tray when needed. In the GigaDevice code, S identifies the 208 mil outline, I the industrial grade, G the lead- and halogen-free package and the final R tape and reel. For Macronix, M means the 16-pin package, I the industrial grade, -10 the 104 MHz speed grade and G the RoHS-compliant, halogen-free option. Confirm the Macronix shipment format with the supplier.

Request date and lot codes, photos of the part marking and packaging label, and traceability records before accepting the lot. On sample units, compare markings with the expected package and read the JEDEC ID. Treat the ID as a functional check and use the incoming inspection process to assess authenticity separately.

See the NOR flash selection guide, the small-batch component QC process and anti-counterfeit checks.

FAQ

Does the same density let me reuse the image?

Verify the flash layout and boot ROM support first. Write and read back the image with the intended programmer, then test cold boot and recovery on the actual board.

Why can a standard SPI read pass while quad reads fail?

Check QE readback, the controller's lane settings and the dummy-cycle count for the selected opcode. Probe the shared signals on the target board while changing modes.

Can I identify the right voltage from the package alone?

Check the family letters and the order label against the datasheet. The two Winbond parts use the same package designation, so the package width alone cannot identify the voltage grade.

Parts mentioned in this article

Request a quote
Send RFQUpload BOM
WhatsApp